yup nice and smooth just takes abit of heat wail being careful so when ya grinf ya still have some weld left

I take it you have full on race bucket thous are not stock seat belt friendly at all best to get a set of 4 point's or you might as well just run no belts at all

I will buy the slider's from momo but I will still have to adapt to the truck

ps I am out of beer grrr the down stairs is so far oh well lol

 

Love the momo seats!

 

yep I hope my ass fit's into them tooo


I have been looking around for some wheels for the truck and I think these would look sick on the truck and I think they will fit?

17x9 5-4.5 bolt 4-1/2bs -12 off set classic 2 Mickey Tompson

Mickey Thompson Performance Tires & Wheels

then run 255 40's all the way around

 

my wheels are 10" width with -9.75mm offset to give you an idea of how it'll look.

 

how much can ya turn lock to lock and does it rub ?

 

Don't ya just hate it when ya have to watch paint dry lol.

I have cure for that thou BEER lol

pic's


here is the part number for angled pcv valve

all painted up ( yes I ground down the welds even thou they were nice )


fittings and hose remember to use oil when assemble an fittings


thats it for now ( paint drying such a bitch)


ps did order bunch of stuff for the truck stay tuned

 

All done but I for got to get new pcv vavle gasket so the old one will have to do




Today I registered for drivers training so I can race at Knox Mountain and i hope my new toys come in before it's training day

Knox Mountain Hill Climb 2012 - Mazda Rx7 - YouTube



But now I have to upgrade my brakes so I am open to idea's

 

yippy skippy I got some momo seat's and my drop spindles came in

still waiting on the other stuff thou

might install seats tomorrow but we will see or install spindles so I can have a hot rod rake going on lol j/k

 

Well I just remembered on how much I hate making seat brackets so simple but such a pain since I wont have sliders on my drivers seat


there are sitting nice and low but I think going to raise it about half an inc so I can see more hood so i will fiddle with it tomorrow


pic's







there not done yet but so they will be

and I got new deck as you can see in one of the pic's

 

son of a bitch I got the wroung 1/8th washer for my passenger seat mounting tab after welding them in the mounting tabs so I will have to grind them off to put popper sized ones in so the seat is safe and wonte pull out in case of car hit wall or car miss hap

and tomorrow i going to sing my streeing caumin inword so my arms are not as bunched up


but I really love these seats sadly I will have to re learn how to drive the truck since the driving position is different then before wont take long really

 

well all is done passenger and driver thank gone I hate doing seats


sweet set up shifter is close to the wheel mixed with short shifts it's like a race car

passenger brakets



bell teck spindles

all painted up

 

Well today went well got the truck lowered but still have to put the sway bars on and stuff since it started to rain


before


New goodies



I had to bend the lower brake heat shield ducting in word



after words



All grab some pic's of the rear tomorrow with the bell tec leafs thus far I love the spring rate.


and tomorrow I will be installing the sway bars

 

Nice parts. Digging the sway bars..

 

Looking good

 

Thanks guys

so today when it get dryer out there going to swap the bars one and mabye if feel like it I will replace my leaking water pump it just slight weep from the weep hole so it not on the really important list


But I am thinking on carpeting my back wall and wondering if should even add sound deading if going to carpet it.
the carpet i plan to use is speaker box carpet same stuff that is on my doors

??????

 

sweet truck man!!! I love the mesh wheels too!!! doe your truck handle very good too!!! mine handled like it was on rails.it had a djm 3/4 inch drop and a dowmey air-intake and a flowmaster 40 series exhaust.it also had 14 inch wheels and tires it was a white 93 base 22re with gray interior and a 5-spd.it was totaled last September. I didn't have any insurance so i'm out a truck.your's is badass!!! is it fun auto crossing too?? I wanted to do that later.i'm getting a white 1998-2004 Toyota Tacoma 2wd sr-5 with gray interior and a 5-spd is next on my list.good job man!!!

 

Still not low enough. lol

 

sorry to hear about your old truck and ya man sure beat's 4x4ing that I used to do for the past 4 years cause I got out of racing.

but now I am back sporting a truck muahahha

race truck sure sit's pretty nice now might have to notch the rear frame but i think i am ok wiht just low profile bumps or just cut mine done

 

thanks man!!! that's cool you auto cross I will get into it as soon as possible!!! I love all your mod's too!!! are you going to 4-link with coilovers or run a i.r.s. with coilovers in the future??? did the swaybars help too with the wheel hop??? did you get better traction too???

 

Don't know yet truck does not move it pouring rain and windy as hell

all most likyl run catracks any way if have ground clearance if not ladder bar or some thing