Recent Content by clark

  1. clark
    Post

    1980 Maui,Hawaii build

    I was waiting for one of you to drift that Hawaiian Cement corner. haha
    Post by: clark, Nov 7, 2012 in forum: 1976-1983 Build-Up/Project Threads
  2. clark
    Post

    Clark's '80 build

    15x8 front and 15x10 rear. Got her back from the mechanic, rebuilt 22R. Not too stoked on paying $1300 for it though. The 20R that was in there...
    Post by: clark, Oct 5, 2012 in forum: 1976-1983 Build-Up/Project Threads
  3. clark
    Post

    MAUI, HAWAII member: NEW 1969 Hilux RN10~Lola

    That truck is unreal. Did you get her off of craigslist here on Oahu? I saw a really clean one for sale over the summer, not sure if its the same one.
    Post by: clark, Sep 21, 2012 in forum: Pre-1975 Build-Up/Project Threads
  4. clark
    Post

    2wd to 4wd fenders?

    x2 .
    Post by: clark, Sep 17, 2012 in forum: Exterior/Body
  5. clark
    Post

    Clark's '80 build

    You need everything except for the torsions. So: Upper Control Arms; Lower Control Arms; Upper Ball Joints; Lower Ball Joints; Spindles AKA...
    Post by: clark, Sep 17, 2012 in forum: 1976-1983 Build-Up/Project Threads
  6. clark
    Post

    Clark's '80 build

    FFFUUUUU Driving on the freeway today, engine started making a really loud knocking noise... Thrown bearing/rod/something? :doah: Anyways, guess...
    Post by: clark, Sep 15, 2012 in forum: 1976-1983 Build-Up/Project Threads
  7. clark
    Post

    Clark's '80 build

    Not nearly the biggest load either. lost the photos of a couple more trips that i made with way more
    Post by: clark, Sep 14, 2012 in forum: 1976-1983 Build-Up/Project Threads
  8. clark
    Post

    T-Bone

    as far as adjusting goes, the after actual suspension swap you shouldn't need to adjust anything. It is only when you install drop spindles that...
    Post by: clark, Sep 11, 2012 in forum: 1976-1983 Build-Up/Project Threads
  9. clark
    Post

    T-Bone

    The only "modification" needed for the swap is drilling one hole in each LCA for the torsions. Other than that, it is a fairly simple swap. I also...
    Post by: clark, Sep 11, 2012 in forum: 1976-1983 Build-Up/Project Threads
  10. clark
    Post

    T-Bone

    I swapped the front suspension out of an '87 into my '80 so that I could BJ flip and put on drop spindles... something you may want to look into....
    Post by: clark, Sep 9, 2012 in forum: 1976-1983 Build-Up/Project Threads
  11. clark
    Post

    Clark's '80 build

    It works! I've put my follow-ups on the backburner as I have had a lot on my plate the last couple months. I have all the content ready for the...
    Post by: clark, Aug 23, 2012 in forum: 1976-1983 Build-Up/Project Threads
  12. clark
    Post

    my 81 diesel

    Nice!
    Post by: clark, Aug 8, 2012 in forum: 1976-1983 Build-Up/Project Threads
  13. clark
    Post

    New Momo shift knob

    Looks good. I like stock/original looking stuff more, but if I didn't, that MOMO knob would be the route I'd go. P.S. My build thread lost...
    Post by: clark, Aug 8, 2012 in forum: Interior/Electronics
  14. clark
    Post

    my 1988 sr5 Xtra cab

    I don't think that you should risk it popping out again. You may be driving down the highway the next time it happens. Buy a new tie rod end.
    Post by: clark, Jul 11, 2012 in forum: 1976-1983 Build-Up/Project Threads
  15. clark
    Post

    77 pickup

    so you are gonna gut it?
    Post by: clark, Jul 8, 2012 in forum: 1976-1983 Build-Up/Project Threads